Frame removal (Aprilia RS125/3)
Read 1.2.1 carefully.
Torque wrench settings:
Remove the engine from the frame; see 6.2.3.
Remove the instrument panel subframe; see 7.4.2.
Remove the front end complete with front wheel assembly; see 7.9.2.
Disconnect the two horn connectors.
Working from the right-hand side, undo and remove the top nut (1).
Remove the bolt from the opposite end and collect the washer.
Working from the right-hand side, undo and remove the nut (2).
Remove the bolt from the opposite end and collect the washer.
Remove the rear swinging arm together with the shock absorber; see 7.11.1.
[The original is published on an online portal: Motoinst.ru]
Remove the side stand; see 7.4.9.
Remove the right-hand rider footpeg bracket; see 7.4.4.
Release and remove the two screws (3).
Remove the left-hand rider footpeg bracket.
Disconnect the connector of the starter relay.
Disconnect the connector of the left light dip switch.
Disconnect the two connectors of the right light dip switch.
Disconnect the two connectors of the right light dip switch.
Remove the seat subframe complete with carburetor, oil tank and airbox, see 7.4.10.
Working on both sides of the motorcycle, release and remove the two screws (4) at the front end.
Remove the two radiator brackets mounted to the battery frame.
Working on both sides of the motorcycle, release and remove the two upper screws (5).
Remove the frame head plate.
Torque wrench settings:
- Shock absorber to frame (1): 50 Nm (5.0 kg·m)
- Linkages to frame (2): 50 Nm (5.0 kg·m)
- Footpeg bracket screws (3): 22 Nm (2.2 Kgm)
- Upper screws (5): 22 Nm (2.2 Kgm)
Note. Each procedure is cross-referred to the relevant section of the manual and some of the operations described there may not be necessary for the job at hand. To avoid redundant work, always make sure you really need to remove a particular component before proceeding.
Remove the engine from the frame; see 6.2.3.
Remove the instrument panel subframe; see 7.4.2.
Remove the front end complete with front wheel assembly; see 7.9.2.
Disconnect the two horn connectors.

Working from the right-hand side, undo and remove the top nut (1).
Remove the bolt from the opposite end and collect the washer.

Working from the right-hand side, undo and remove the nut (2).
Remove the bolt from the opposite end and collect the washer.
Remove the rear swinging arm together with the shock absorber; see 7.11.1.
[The original is published on an online portal: Motoinst.ru]
Remove the side stand; see 7.4.9.
Remove the right-hand rider footpeg bracket; see 7.4.4.

Release and remove the two screws (3).
Remove the left-hand rider footpeg bracket.

Disconnect the connector of the starter relay.

Disconnect the connector of the left light dip switch.

Disconnect the two connectors of the right light dip switch.

Disconnect the two connectors of the right light dip switch.

Remove the seat subframe complete with carburetor, oil tank and airbox, see 7.4.10.
Working on both sides of the motorcycle, release and remove the two screws (4) at the front end.
Remove the two radiator brackets mounted to the battery frame.

Working on both sides of the motorcycle, release and remove the two upper screws (5).
Remove the frame head plate.

See this article in russian language
This article has been reviewed: Artemy Kuzmin
Similar articles about motorcycles of other brands
Installing auxiliary frame (raising frame unit clear of… BMW R 1150 GS (1999-2004)Brakes and frame — description and specification Ducati ST2 (1997-2003)
Frame and chassis specifications Harley-Davidson V-Rod (2002-2006)
Description of frame design Honda CB 400 SF (1992-1999)
Frame exploded view Kawasaki ZX6R/ZX600J (2000-2002)
Comments and feedback from visitors
No comments yet, you will be the first!
- Information for owner
- Introduction to manual
- Maintenance
- Troubleshooting
- Engine and systems
- Engine repair
- Fuel system
- Cooling and lube system
- Running gear and frame
- Frame and hinged elements
- Front suspension and handlebar
- Rear suspension
- Brake system
- Wheels and tires
- Electric equipment
- Equipment and devices
- Starting and charging system
