MotoInst.ru
Mobile
version
Articles
& news
Site
map
Feed
back
Add to
bookmark
English Русский
Aprilia
BMW
Ducati
Harley
Honda
Kawasaki
Suzuki
Triumph
Yamaha
Aprilia:
RS-series▾
RS125 [3] (1998-2005)
Shiver▾
SL750 (2007-2016)

Exhaust valve installation (RAVE) (Aprilia RS125/3)

  • Main
  • Aprilia
  • RS-series
  • RS 125 [3]
  • Engine and systems
  • Engine repair
  • Exhaust valve installation (RA…
0
Contents: Complete valve installation ↓ Installation after partial removal ↓
Read 1.2.1 carefully.

Torque wrench settings:
  • RAVE valve screws (1): 10 Nm (1.0 kg·m)

Remove the fuel tank; see 4.1.1.

Remove the battery together with the battery box mount; see 7.2.1.

When installing a RAVE valve to a derated engine, first remove the fixed slide. This is done by unscrewing the two screws (1). Collect the washers.

When installing a RAVE valve to a derated engine,…


Complete valve installation



Insert the exhaust valve assembly complete with seal (5) into the cylinder.

Note. Change the seal (5) on assembly.


Use the two screws (1) with washers of the fixed slide to secure the exhaust valve assembly.

Use the two screws (1) with washers of the fixed…


Fit the control unit to the battery bracket using the two screws (2).

Fit the control unit to the battery bracket using…


Connect the control unit connector to the wiring harness.

Connect the control unit connector to the wiring…


Installation after partial removal



Connect the Bowden cable (3) to the valve stem housing (4).

Rotate the valve stem housing (4) through 180°.

Note. The cable anchor point must be pointing downwards.


Refit the dust cover.

Insert the exhaust valve assembly complete with seal (5) into the cylinder.

Note. Change the seal (5) on assembly.


Tighten the two screws (1) with washers of the exhaust valve assembly.

Tighten the two screws (1) with washers of the…


Warning! Check the exhaust valve assembly as follows after installation.


With the valve fully open, the valve stem must be flush with the exhaust port. This inspection must be done with the exhaust flange removed; see 6.1.1.

Make sure the exhaust valve moves freely.

Make sure the exhaust valve moves freely.
See this article in russian language
This article has been reviewed: Artemy Kuzmin
◀ Previous
Aprilia RS125 3: Engine repair
 

RAVE valve component inspection
Exhaust valve removal (RAVE)
RAVE valve specifications
Installing the engine into the frame
 
Similar articles about motorcycles of other brands
Valve clearance adjustment chart exhaust valve Kawasaki Versys 650 (2007-2025)
EXCVA (exhaust control valve actuator) and EXCV (exhaust… Suzuki Boulevard M109R (2006-2025)
Checking/adjusting valve clearances BMW R 1150 GS (1999-2004)
Checking valve clearances Ducati ST2 (1997-2003)
Exhaust Sound Management System Harley-Davidson V-Rod (2002-2006)
Comments and feedback from visitors
No comments yet, you will be the first!
 


Add up two numbers: 17 + 50

       



 

 
RS125 3 (1998-2005) 
  • Information for owner
  • Introduction to manual
  • Maintenance
  • Troubleshooting
  • Engine and systems
  • Engine repair
  • Fuel system
  • Cooling and lube system
  • Running gear and frame
  • Frame and hinged elements
  • Front suspension and handlebar
  • Rear suspension
  • Brake system
  • Wheels and tires
  • Electric equipment
  • Equipment and devices
  • Starting and charging system
Aprilia • BMW • Ducati • Harley • Honda • Kawasaki • Suzuki • Triumph • Yamaha
MotoInst.ru © 2021–2026 | Sitemap | Articles | Contacts | | Add to bookmarks | Mobile version
 
Cookies are used for better functioning of the site ⚙️ Do you accept?